深圳厂房装修环氧树脂地板漆的保养维护的方法
深圳厂房装修环氧树脂地板漆的保养维护的方法，在施工及维护方面潍坊地坪漆建议作如下处理：
一、深圳厂房装修环氧树脂地板漆养护要求：
1、清洁地面时请用软质拖把或干湿两用吸尘器，可用清水或清洁剂清洗，但请注意地面湿滑;
2、表面保洁,环氧地坪表面清洗方法简便，一般用水擦洗。如遇难清洗的污渍，使用清洗剂即可，也可用工业去脂剂、除垢剂等，然后再用水冲洗干净。对于相当顽固的污渍，也可用机械清洁的办法，但对地面不要施压、磨损过大以影响地面的平整及光泽。
3、若因使用时间较长而造成磨损或刮花、小面积可进行局部修补，若面积较大则建议重新滚涂一次。
4、凡进入车间人员须换鞋(以免将处面泥砂带入车间而划伤地面);
5、推车，板车之车轮请用硬质或弹性胶轮，并厂房内外分开使用;
6、避免化学品的污染
7、请勿滥用机械,使用时尽量避免对地面过重的敲击，不要用非常重的或者坚硬的物品敲打地面，除非工作的需要，请避免频繁的不必要的磨损。尤其是对于ESL地坪，为保持其光洁细致、外表美观的优点，特别注意避免钢轮等的交通;不要有过重的交通及负载，与地面接触处要注意避免产生划痕。
8、凡是硬件：如铁椅、铁桌、铁货架等，须将其脚用软质塑料或橡胶包裹以免在使用过程中划伤地面;
二、深圳厂房装修环氧树脂地板漆施工方法：
基面打磨、裂缝修补→环氧底漆一道→批刮环氧砂浆层→环氧腻子层→环氧色漆层→环氧罩光层
三、深圳厂房装修环氧树脂地板漆施工环境：
基面含水率：在6%以上时不能施工非水性环氧地坪;2.空气中湿度：在85%以上应停止施工;3.施工温度：低于5℃应选用特殊配方。对于一些大型的车间厂房或者车库等区域的地面处理方式，都会采用环氧地坪漆来使用，为了环氧地坪能有表面良好的光洁度和美观的效果。
深圳厂房装修环氧树脂地板漆的保养维护的方法由深圳祥云装饰设计工程有限公司分享，如果大家喜欢转载请注明出处：http://boshengdazs.com/。
Shenzhen factory decorate epoxy floor paint the maintenance method
Shenzhen factory building decoration epoxy floor paint, the method of the maintenance of the construction and maintenance of weifang floor lacquer Suggestions as follows:
The, shenzhen factory decorate epoxy floor paint maintenance requirements:
1, please clean the ground with soft mop or dry wet amphibious vacuum cleaners, available water or cleanser, but please note the ground wet.
2, surface cleaning, epoxy floor paint surface cleaning method is simple, general water scrub. Such as killing cleaning besmirch, the use of cleaning agent can, also can use industrial degreasing agent, cleaner, etc., and then rinse clean with water. For quite a stubborn stains, also can use mechanical cleaning solution, but don't pressure, wear and tear on the ground is too large to influence the leveling of the ground and luster.
3, if due to use for a long time wear or scratches, small area can repair locally, if it is recommended to roll a larger area.
4, who enter the workshop personnel shall change the shoes in order to avoid the surface mud into the workshop and scratch the ground);
5, cart, wheels of scooter please use of rigid or flexible roller, and building internal and external used separately;
6, to avoid contamination of chemicals
7, please do not abuse machinery, when using, as far as possible to avoid heavy knock on the ground, don't use heavy or hard goods hit the ground, unless the needs of work, please avoid unnecessary wear and tear. Especially for ESLfloor, to maintain its bright and clean and meticulous, beautiful appearance, the advantages of paying special attention to avoid traffic such as steel wheel; Don't be too much traffic and load, contact with the ground should payattention to avoid the scratch.
8, all hardware, such as iron chairs, iron table, iron shelves, etc., to its feet with soft plastic or rubber from scratch in the process of using the ground;
Second, the shenzhen factory decorate epoxy floor paint construction method:
Reference plane grinding, the crack repair - a epoxy primer - batch blows layer of epoxy mortar to epoxy putty layer - > epoxy paint, epoxy cover layer of light
Three, shenzhen factory decorate epoxy floor paint construction environment:
Base moisture content: not construction in more than 6% of waterborne epoxy floor; 2. The humidity in the air: above 85% should stop construction, 3. The construction temperature: less than 5 ℃ should choose special formula. For somelarge area of workshop workshop or garage, ground handling, using epoxy floor paint to use, in order to epoxy floor can have a good surface finish and beautiful effect.
Shenzhen factory decorate epoxy floor paint the maintenance method of sharing by shenzhen xiangyun decoration design engineering co., LTD, if you like them reprint please indicate the source: http://boshengdazs.com/.
